Tuesday, July 26, 2016

How to Re-Peak a DIRECTV Satellite Dish for Better Signal

The most effective method to Re-Peak a DIRECTV Satellite Dish for Better Signal

Redesigned on June 5, 2013

DIRECTV satellite dish.

DIRECTV satellite dish.

In the event that you are encountering next to zero satellite show signal, you may need to re-top (or re-point) your satellite dish to get or calibrate the telecast signal. On the off chance that you like to settle the issue yourself instead of getting out a specialist, the accompanying guidelines guide you through the accompanying strides: (1) re-setting your DIRECTV collector; (2) re-topping your satellite dish; and (3) re-securing your satellite dish.

Note: Before re-topping your satellite dish, read the Safety Instructions that came in your DIRECTV collector box or accessible at DIRECTV's site.

Hardware and Tools

You will require the accompanying hardware and apparatuses to re-crest your dish:

Stepping stool of suitable tallness to achieve your satellite dish

7/16-inch or 1/2-inch sickle wrench contingent upon size of satellite dish

7-inch attractive air pocket level

Compass

DIRECTV collector

TV

Cautioning: Follow legitimate stepping stool wellbeing precautionary measures when utilizing your step. Inability to do as such could bring about real harm.

Re-Setting Your Receiver

On the off chance that you are seeing the Searching for Satellite message on your TV screen, separate the force line from your DIRECTV beneficiary for 30 seconds. In the wake of holding up 30 seconds, reconnect the force line to your DIRECTV recipient. In the event that the hunting down satellite message comes back to your screen, you should re-crest your satellite dish by altering the azimuth and rise settings.

Settings and Help menu

Settings and Help menu

Satellite Dish Setup menu

Satellite Dish Setup menu

Signal Strength screen

Signal Strength screen

Test Signal Strength screen

Test Signal Strength screen

Re-cresting Your Satellite Dish

Before re-cresting your satellite dish, get to the Signal Meters menu from the Settings and Help menu on your beneficiary to utilize the sign meter to screen the telecast sign to your satellite dish. To get to the Signal Meters menu:

Press the menu catch on your remote.

Select Settings and Help on the left hand menu.

Select Settings.

Select Satellite on the left hand menu.

Select View Signal Strength on the base right-hand screen (look to it utilizing the bolts on your remote).

Select Signal Meters on the base right-hand screen.

Re-position your TV to be in your observable pathway while re-topping your satellite dish. On the off chance that conceivable, have a companion screen the sign meter and transfer the telecast signal quality to you while you are re-cresting your satellite dish.

To re-crest your dish you should play out these assignments:

Watch that the pole is level.

Conform the azimuth of the satellite dish.

Conform the height of the satellite dish.

Cautioning: Use alert while conforming the pole. The heaviness of the satellite dish may bring about the pole to swing down and hit you, an observer, or adjacent items. This could bring about real harm or harm to adjacent articles and the satellite dish. Continuously hold the pole around its outside perimeter to avert damage to your fingers.

The bolster sleeve nuts are situated on the back of your satellite dish.

The bolster sleeve nuts are situated on the back of your satellite dish.

Watch that the pole is level. On the off chance that the show signal quality is lost in view of solid wind or other severe climate, the pole supporting your satellite dish may never again be level. On the off chance that the pole has not moved, you can skip to the following stride, Adjust the azimuth of your satellite dish. To check if the pole is level:

Position your step as important to achieve your satellite dish.

Cautioning: Ensure your step is situated on a steady and level surface to anticipate falling and real damage.

Utilize your 7/16-inch (or 1/2-inch wrench, contingent upon the span of your satellite dish) to unscrew the bolster sleeve nuts on the back of your satellite dish.

Expel your satellite dish and tenderly place it on the ground or other secure area.

Place your 7-inch attractive air pocket level on the pole to confirm that it is opposite (or 90 degrees) to the ground.

Re-level the pole as important to re-position it to be opposite to the ground.

Place your satellite dish painstakingly back onto the pole and re-fix the bolster sleeve nuts so that your satellite dish is secure, yet versatile.

When you have put your satellite dish back on the pole, you can change the azimuth.

Alter the azimuth of your satellite dish. The azimuth alludes to the revolution of the entire satellite dish around a vertical pivot (the pole). It is the flat (side-to-side) edge. To conform the azimuth of your satellite dish:

Utilize your compass to figure out which course is west.

Turn your satellite dish gradually from the west towards the east, while observing the show signal level on the sign meter of the Dish Pointing menu.

Turn your satellite dish towards the east once you see the show signal begin to increment. At the point when the show signal begins to diminish once more, pivot your satellite dish back towards the west until the sign meter has achieved the most elevated sign level.

Fix the bolster sleeve nuts totally and guarantee your satellite dish can no more move.

In the event that the show signal quality is still not to sought level, you can likewise alter the rise of your satellite dish. The height of your satellite dish ought to just need conformity if the rise jolts have come free.

The height jolts are on either side of the back of your satellite dish.

The height jolts are on either side of the back of your satellite dish.

Alter the rise of your satellite dish. The rise alludes to the edge between the satellite dish guiding heading, specifically towards the satellite, and the nearby even plane. It is the vertical (up-down) point. To alter the rise of your satellite dish:

Relax the height jolts on either side of the back of your satellite dish, while supporting your satellite dish, with the goal that it is still versatile.

Lift your satellite dish vertically, while observing the show signal on the sign meter on the Dish Pointing menu. On the off chance that the sign level begins to reduction, bring down your satellite dish until the sign meter has achieved the most astounding sign level.

Once the sign meter has achieved the most noteworthy sign quality, quit lifting your satellite dish.

Fix the rise jolts totally and guarantee your satellite dish can no more move.

When you have fixed the rises jolts, you can re-secure your satellite dish.

Re-Securing Your Satellite Dish

After you have balanced the azimuth and balanced the rise, affirm all bolster sleeve nuts and height fasteners are fixed. Affirm on the sign meter of the Dish Pointing menu that the show signal quality is at its most abnormal amount.

https://turbofuture.com/home-theater-audio/How-to-Re-Peak-a-DIRECTV-Satelite-Dish-for-Better-Signal

No comments:

Post a Comment